Xenon Circuits
-
In this strobe-light, two circuits are needed; one circuit charges a capacitor placing 320 V de between the cathode and anode of the flashtube. The other circuit provides bursts of approximately 4000 V to trigger the flashtube into conduction. The.... -
This strobe gives a visual indication of a sensor input. The input signal causes Ul, a light dependent resistor, to chaijge CI.. -
The circuit is activated by an LED/photoresistor isolator (Ul), which is a combination of a light-dependent resistor (LDR) and an LED in a single package. That device was chosen because of its high isolation (2000 V) characteristic, which is necessary.... -
This strobe light operates from standard 120-Vac power. Rl limits the amount of current applied to the voltage doubler stage, which is comprised of CI, C2, C3, Dl, D2, C4, C5, and C6. Capacitors CI, C2, and C3 are connected in parallel and form a.... -
Initially the neon and xenon lamps are not conducting and act like a very high (almost infinite) resistance. Capacitors Cl and C4 in conjunction with DI and D2 form a voltage doubler circuit, which can charge C2 up to about 300 Vdc after several ac cycles..... -
Tubular Xe lamp power, high brightness, known as the "little sun." Tubular xenon lamp wiring shown in Figure 2-6... -
This circuit will give provide a Good Strobe Effect for a variety of Portable Uses. Nominal current draw is "up to about" 1 amp at 12 volts. Depending on value of capacitor on pin 2 of the 555 and the particular choke that is used... -
This Adjustable Strobe Light is the bigger brother of the plain old strobe light. This one uses a much more powerful "horse shoe" Xenon tube which produces more light. You can also control the flash rate up to about 20Hz. Do not look directly at the flash.... -
This DC-DC converter ("inverter") needs nothing but unmodified Radio Shack parts. You don`t need to build or wind any coils or transformers. This is a cheap-and-dirty experimenter`s circuit. I tested this and it worked for me, but I disclaim all warranties!.... -
Figure 1 shows a complete circuit for an emergency lamp that operates from a 12V automotive battery. The xenon flash tube requires a 250V-dc anode voltage and a 4-kV trigger pulse. To generate the 250V dc, IC1, a switching regulator controller, and T1, a....
-
Cell phones and PDAs are approaching the limit for small form factors, but their feature sets are growing with new functions such as built-in cameras and even video cameras. The initial in-phone cameras were basic, low resolution devices with little in the....
-
Since the circuit operates at greater than mains potential and is not isolated by a transformer, it is extremely dangerous. The DC operating potential is about 340V, and there is more than enough stored charge to kill you many times over (although in my.... -
Flash lamp is made ??with experimental parts removed from a disposable camera flash circuit.Xenon try to use what I think is easily affordable experiment. AC100V to a voltage doubler rectifier, DC voltage of about 270V is derived. This voltage is R2, C3 is.... -
The way that this circuit works is as follows. The AC line voltage is rectified by D1 and D2 which connects to a voltage doubler circuit made up of the two 22uf capacitors. The Flash Freq. Pot and the 10uf capacitor charge up which triggers the Diac and.... -
If you have no idea what is a "strobo", "strobe", "stroboscopy" or whatever way it is called, it is simply a flashing light. It is usually used on police cars, 'disco' places and many interesting applications, including scientific ones. This project is.... -
This circuit typically uses a voltage around 300 volts for the main high voltage supply and needs a low voltage supply of typically 6 to 15 volts. 555 pin connections not shown above: 1 goes to ground / negative of both low and high voltage supplies. 4,8....
-
The power supplies for electronic flash and strobe equipment operate at extremely lethal voltage and current levels. The energy storage capacitors in even the smallest disposable camera flash operating from a 1.5 V AA battery can be deadly under the wrong....
-
The way that this circuit works is as follows. The AC line voltage is rectified by D1 and D2 which connects to a voltage doubler circuit made up of the two 22uf capacitors. The Flash Freq. Pot and the 10uf capacitor charge up which triggers the Diac and.... -
This is one of my stroboscope designs. Usually many stoboscope circuit work directly from mains voltage, but this circuit uses 12V DC intead od mains AC. This is very good idea if you don't want to mess with direct mains voltage connected circuit or you want.... -
This page contains some information on circuits which can be used for triggering stroboscopes from external circuits. The circuit here are designed to be integrate to strboscope circuits so that they can triggered using external trigger pulse. The standard.... -
A stroboscope is an instrument which is used to view the object which is moving rapidly with a periodic motion as if they are at rest. The strobe light flashes at a frequency that synchronizes with the resolution of a wheel or moving object which seems to be.... -
This is Xenon Strobe Light circuit, model continual use a tube Xenon at give many brightnesses. By can fine blink fast or slow get , with VR1. By have SCR... -
This circuit is used for remote photographic flash units that flash at the same time as the flash attached to the camera.This circuit is designed to the trigger cord or hot shoe connection of a commercial portable flash unit and triggers the unit from the.... -
Xenon lamp, strobe light circuits, xenon strobe, photo flash, photoflash,schematics or diagrams, all free to use. My inspiration came from a strobe circuit that was in a school fire alarm.... -
This circuit is xenon lamp flash detector. It has a very low standby current requirement yet has very high sensitivity toward the light flashes from a xenon lamp. When connected to a flip/flop it can serve as an on on/off controller... -
The circuit was taken from one of the old elektor electronics magazine and it is indeed a very cute little circuit which may be used for creating high intensity lighting effects during festivals, parties and fun gatherings. Diodes D1 and D2 along with the.... -
The AAT1265 evaluation board provides a platform for the testing and evaluation of the AAT1265 low voltage 2MHz Step-up Regulator The evaluation board demonstrates suggested size and placement of external components to main- tain output voltage regulation.... -
The DS2422 temperature/data logger combines the core functions of a fully featured data logger in a single chip. It includes a Temperature Sensor Real-Time Clock (RTC), memory, 1-Wire Interface and serial Interface for an Analog-to-digital converter (ADC),.... -
Power demand in portable designs CAN require in some specific application more than 1 A. A method consists in paralleling two DC to DC converters on the same load instead of placing a single higher current converter with lower switching frequency. This....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
White LEDs have a rated current at a voltage drop of about 3.3 to 3.4 V. It is ideal to be...
If a NiCad battery is discharged to a point at which the lowest capacity cell becomes fully...
Have you ever wanted to make a line following robot but the infrared sensors were too expensive...
This design adopts a well established circuit topology for the power amplifier, using a...
With a 9 V DC battery, it worked fine. But because of a less DC power, solenoid was not...
This circuit detects spikes in voltage around 18v. It is used to detect when a battery becomes...
This is a modified version of the first SSTC I built, the Kaizer SSTC I. It uses the same...
Most of the peripherals that interface with PC uses USB port. The computers power supply circuit...
How to build a voltmeter for DC voltage measurements without using multimeter testing This is a...
Audio metering is present in almost any equipment that plays or records audio from cell phones...
A long time ago when telephones were so simple almost nothing could go amiss from an electrical...
The open-loop concept of oscillator design is often met with considerable skepticism by engineers...
This circuit has an advantage in that almost all of the energy in the collapsing magnetic field...
AC-DC-AC circuit when the power transistor as a switching device with analog control if built...